Homemade bicycle wheelbarrow. How to make a garden wheelbarrow with your own hands - an overview of the best ideas for giving (135 photos)

Wheelbarrows or carts used by gardeners and gardeners have a lightweight design and are not designed to carry too large and heavy loads. A do-it-yourself garden wheelbarrow is made quite simply even from unnecessary or improvised materials, which allows you to get a reliable and budgetary means of transportation.

Garden wheelbarrows: types of their advantages and disadvantages

By their design, all garden wheelbarrows are a beveled metal body equipped with a wheel or wheels, a handle and legs that provide stability during loading and unloading.

Single wheel design

One-wheeled equipment is designed to transport fairly light loads, including crops, weeds and horticultural fertilizers.

The wheelbarrow is only suitable for use on garden paths, asphalt

Advantages and disadvantages: the model is quite affordable, easily overcomes corners and turns, but has optimal cross-country ability only on flat and hard surfaces, and movement on the ground causes noticeable difficulties.

Two wheel design

More lifting models, which are distinguished by better maneuverability and are currently the most popular among the owners of summer cottages.

A wheelbarrow is not as maneuverable as a one-wheeled one, but is more stable and reliable

Advantages and disadvantages: the model does not get stuck on rough terrain, has good cross-country ability and does not require much effort, and is also quite stable during loading / unloading.

Tricycle design

A garden three-wheeled wheelbarrow is very roomy and has a solid load capacity, but the release of such models has been established by a small number of manufacturers.

The design combines the advantages of one- and two-wheeled wheelbarrows, but its price is much higher.

Advantages and disadvantages: the model is easy to operate, most stable, does not require a lot of force when moving, has good maneuverability, but the cost is higher than that of one- and two-wheeled counterparts.

Trolley - four-wheeled wheelbarrow

Four-wheeled models are the so-called heavy artillery in the range of modern garden wheelbarrows. A feature is the presence of a pair of axles, due to which the trough has maximum load capacity.

The only drawback of such a product is the high cost compared to other models.

Advantages and disadvantages: the model has excellent stability, and the addition of a special tipping mechanism greatly facilitates unloading, but the price for such products is often very high.

Preparing to make a wheelbarrow

Of course, all of the above designs may well be made by hand, but to get a durable, reliable and easy-to-use garden wheelbarrow, you need to carefully consider the choice of materials.

Which wheels to choose

The equipment of a garden wheelbarrow involves the use of plastic, molded, made of rubber, and pneumatic wheels with treads. The first type makes the structure light, but not too heavy.

It is impossible to make a reliable car without good wheels

One option is to purchase new wheels. The implementation of such elements for wheelbarrows is now carried out by garden centers, construction markets and retail outlets. The best option is represented by solid polyurethane wheels and high-quality rubber four-ply tires.

This product is suitable for carrying light loads.

It is quite acceptable to use wheels from bicycles and other equipment. At the same time, it must be remembered that cast wheels are more durable and are not able to deform even under a heavy load, and an air-filled rubber chamber has good shock absorption and a smooth ride.

body material

Prefabricated structures most often have a body made of aluminum or steel. At the same time, the aluminum bowl is more durable, and the steel trough must have a zinc coating. In the manufacture of a garden wheelbarrow with your own hands, a variety of materials can be used:

sheet metal must be galvanized or powder coated, which prevents the development of rust;
wood is a more affordable material, but such a body will need to be subjected to aseptic processing and staining;
the plastic body is lightweight and resistant to corrosive changes, but is not resistant to mechanical damage.

The most budget option would be to use old structures in the form of a half of a barrel or a metal bed back. Some craftsmen make a wicker car body from wicker twigs.

The shape of the body can be trapezoidal, with a beveled front (this allows you to quickly and easily unload bulk contents), as well as the traditional square (in which the load is placed more accurately).

What to make pens

Most often, handles are made of metal with special light anti-slip rubber pads. It is quite possible to provide any wooden structures with a simple hand-made wooden handle. Corrugated rubber or plastic nozzles with special notches for fingers are very convenient in work.

Corrugation on such a product must be mandatory

At the same time, it must be remembered that the space between the mounted handles must necessarily be optimal for the most comfortable maneuvering and reducing the load on the hands or the musculoskeletal system. The spacing of the wheelbarrow handles should allow the body of a person to fit with the remaining total free distance of about a quarter of a meter.

Depending on the purpose, one transverse handle or a pair of longitudinal handles is fixed to the garden wheelbarrows. The longer handles make carrying loads very comfortable and easy, but the gripping point needs a standard bend to prevent wrist twisting during operation. It should be noted that models with two handles must be pushed, and wheelbarrows equipped with one handle can be not only pushed, but also dragged.

What tools will be needed

The set of tools that you will need to use when constructing a garden wheelbarrow with your own hands depends on the materials of manufacture:

hammer;
tape measure, ruler and marker;
hacksaw for working with metal or wood;
screwdriver;
welding machine;
Bulgarian;
set of wrenches.

If it is necessary to perform staining or processing with special compounds, it is important to prepare brushes of different sizes in advance.

Making a wheelbarrow with your own hands: step by step instructions

The advantages of self-manufacturing a garden wheelbarrow are that the dimensions and design of such a means of transporting goods can be individual, depending on the main purpose and needs.

Manufacture of a single-wheeled steel structure

A sketch of a future car is an important part of the work

A one-wheeled wheelbarrow is the easiest and most affordable option in terms of cost.

Steps for making a steel model:

Development of a preliminary sketch indicating the dimensions and configuration, the location of the handles, stops, wheelset and axle.
Cutting a steel sheet and cutting with a grinder.
Making a bowl using a welding machine.
Manufacturing and welding of a support post from a metal angle or pipe 2.5 × 2.5 cm.
Wheel installation.

Handles and supports should be made of sufficiently thin metal tubes that facilitate construction.

from wood

No less popular is the option of a wooden one-wheeled wheelbarrow.

The frame consists of two guides and a pair of transverse bars

This version is suitable for those who know how to work with wood.

The simplest model is performed in accordance with the following technology:

Production of a supporting frame from a pair of guides and a pair of transverse bars, which are located at an angle of 22 ° to each other. Grooves for the wheel axle are made in the front of the frame. On the inside, metal plates are installed that increase the strength of the structure.
Without a metal plate, the front of the frame can become the weakest point in the entire structure.
The bottom part is assembled using a planed board with dimensions of 2.0x8.0x47.5 cm. Screws are used as fasteners, which are fixed on the guide frames.
The desired size of the bottom is formed after it is mounted on the frame
The cutting line is marked, after which cuts are made on both sides with a circular saw at the desired angle.
Such a wheelbarrow is convenient for transportation and unloading.
For the manufacture of the front and rear boards, planed boards with dimensions of 2.0x0.8 cm are used. Planed boards with dimensions of 2.0x10.0 cm are used for the side boards of the wheelbarrow. The strength of the boards is ensured by fixing special elements in the corners.
The ease of use and maneuverability of the product depends on compliance with the dimensions and angles between the elements.
Wheelbarrow stops are made of wooden bars, which can significantly improve the rigidity of the body part of the structure.
It is not necessary to buy a wheelbarrow for a wheelbarrow - you can make it yourself
A pair of bearings is installed on both sides inside the hub of a wooden wheel, after which the axle is installed, washers are put on, and clamping is carried out using blind nuts.
The service life of a wheelbarrow largely depends on the durability of the wood from which it is made.

The finished structure should be treated with special compounds that will protect the wood from negative external influences and extend the life of the garden cart.

Production of a two-wheeled cart

The two-wheeled design is stable, does not roll, and also minimizes the load on the hands and back of the person.

Plastic is a great option for making a case because it is more durable than wood and cheaper than metal.

Do-it-yourself technology for making a garden wheelbarrow from an old barrel:

Cut a plastic or metal barrel in half.
Weld a rectangular frame from metal profiles 2.5 × 2.5 cm.
Cut out the footboard for attaching the case.
Install and secure with wheel nuts.
Weld a metal profile handle with a holder onto the back of the frame.

At the final stage, a handle is formed from several shock absorber bushings, which are arranged in one row.

Video: do-it-yourself two-wheeled construction, master class

Making a tricycle

Homemade three-wheeled carts are convenient and practical. The third wheel in such designs facilitates the control of equipment and increases its carrying capacity. Unlike wooden counterparts, metal carts are assembled from top to bottom.

The trolley is suitable for transporting heavy loads

Do-it-yourself steps for making a three-wheeled cart:

Selection or welding of a steel trough.
Checking the tightness of the container.
Welding the frame in accordance with the dimensions of the trough.
Fixation of the rear wheelset and front guide wheel.
Welding of one U-shaped handle or a pair of separate handles.

It is quite possible to use a children's bicycle as a wheel base.

Making a four-wheeled wheelbarrow

Four-wheel type structures are usually made of metal. This allows the wheelbarrow to withstand the weight of the load up to 90-100 kg. Assembling such a model with your own hands involves the use of a locksmith tool kit.

DIY four-wheel garden cart manufacturing steps:

The reliability of such a car is achieved at the expense of maneuverability

Carry out the necessary calculations and sketch.
Choose a container, which can be an ordinary steel trough.
Weld a frame frame structure made of rectangular metal pipes.
Weld a U-shaped handle to the frame.
Install at the bottom of the wheel structure.

Garden wooden cart as an element of decor

Recently, wooden garden wheelbarrows have almost completely lost their utilitarian, main purpose and moved into the category of elements for decorating the landscape. In the body of this design, a container decorative garden can be equipped or flower pots with beautifully flowering plants can be installed.

Such a product will decorate the garden plot

Designs can be equipped with one, two or even four wheels. The latter option is more stable and roomy, due to which it is most often used in landscaping the local area. For manufacturing, it is recommended to use hardwoods - maple, oak, birch and elm.

The most exotic type of material that can be used to make a do-it-yourself garden wheelbarrow is durable and environmentally friendly wicker.

Beautiful garden decoration

Such an unusual and very beautiful "basket on wheels" can be used to place pots of flowers or green vitamin crops.

Video: do-it-yourself wheelbarrow-flower garden

What determines the cost of products

The average price of wheelbarrows and trolleys varies greatly depending on a range of factors, including:

load capacity;
body volume;
number and type of wheels;
material used in the manufacture.

It is necessary to take into account the fact that the cost of garden wheelbarrows varies not only depending on the technical characteristics and equipment, but also on the reputation of the company producing the brand. Therefore, if you have the materials and tools necessary for the manufacture of the structure, it is advisable to do such work yourself.

When choosing the design of a garden wheelbarrow, it is important to consider the main characteristics of such a device and its purpose. For frequent transportation of overall and heavy loads, preference should be given to the manufacture of stable and more maneuverable models, and with the infrequent movement of the lightest materials, a simple, lightweight version of the wheelbarrow will do just fine.

Nothing makes the work of a gardener or builder in the country easier than a two-wheeled wheelbarrow. This primitive and prehistoric device is indispensable in everyday life, despite its simplicity. The cost of a tool in a supermarket can be very upsetting, and company stores can even scare. Why pay more if you can make a two-wheeled wheelbarrow with your own hands and save 5000-7000 rubles? Now we will consider detailed instructions for its manufacture and schemes that will help realize our "malicious intention"!

The choice of drawing and design features of a two-wheeled cart

To begin with, we will discard what will really be inconvenient and impractical. We remove carts and wooden structures from the list. Why? Both are very heavy, why should we tear our backs or push what is not being pushed? In addition, a wood body will fall apart in 2-3 years, or it must be constantly varnished, dried after use and hidden from rain. And since we value our time, we will pay attention only to home-made metal cars.

Now let's decide how many wheels you need. Four and three wheels - we immediately discard, since we need a light and maneuverable wheelbarrow, and not a cart for a tractor or motorcycle. Most gardeners prefer a one-wheel design, but it has a significant drawback - it can carry less weight, it is unstable, and is not suitable for uneven surfaces. Tipping the load to the side is easy. In general, one wheel for a wheelbarrow is good, but two is better. The general drawing of the frame and body of the car will be something like this:

Now let's decide on the cost. Although, why decide on it ... If you do not want to buy it in a store, then you share our opinion and want to do everything cheap and cheerful. That is exactly what will happen. Our do-it-yourself garden wheelbarrow will cost no more than 750 rubles, provided that we buy materials in a regular supermarket. If you have scrap metal lying around in the country, old metal profiles and there is at least 1 wheel for a wheelbarrow, then it will cost you almost free.

From words to deeds: how to make a homemade car in 4 hours

First, we will make a frame on which the body of the car will be installed. Our the design is designed to carry no more than 200 kg, so take this into account and do not exceed the load to avoid tool breakage. Dimensions may vary, but we chose the average parameters that are most often used in garden and construction two-wheeled cars. Now let's move on to the selection of materials, tools and assembly of the structure.

STEP 1: weld together 2 load-bearing sides. You will need 2 metal profiles with sides 35x35 mm and a length of 140-150 cm, as well as a corner 25x25 mm 2 meters long. We lay metal profiles opposite on a flat surface, cut off 5 corners of 40 centimeters each and lay them out between our load-bearing sides of the frame. We weld the corners on both sides to the metal profile as shown in the diagram.

STEP 2: we make pens. We take a thick rubber hose with an inner diameter of 34 mm and a length of about 40 centimeters, cut it in half. A homemade garden wheelbarrow should have non-slip handles, so the hose is pulled very hard on the metal profile. It must be held over the fire, constantly scrolling, so that it warms up well. Then, with a slight movement of the hands (legs or improvised objects) or with the help of an auxiliary worker, we pull the hose onto the end of the frame, as shown in the diagram. The hose will cool down and it will no longer be possible to remove it. If it is difficult to pull, you can lubricate the metal with shampoo, soap or grease Helps in most cases.

STEP 3: weld axle. This can be done later, but we will do it now, because it is much more convenient. We turn our frame for a homemade wheelbarrow on wheels and weld a metal bar with a diameter of 22 mm (this is the running size for tubeless wheels). You can choose a different diameter, if you have any wheels for a wheelbarrow in mind. We recommend using truck tubeless wheels with a diameter of 40 to 50 cm - they are almost eternal.

If your homemade car for a summer residence has to carry a large load off-road (obstacles up to 5-8 cm in height), then it is better to use wheels with a larger diameter. If you have a very flat area or even concreted, it is better to choose 35-40 cm each, no more - there is less resistance, it is more convenient to control and it is easier to push. In addition, small wheels are cheaper.

If you want to learn how to make a garden wheelbarrow with your own hands at no significant cost, then you will need to pick up wheels from a moped or motorcycle. As a donor, you can use an old walk-behind tractor on metal wheels or a seeder. Be sure to measure the inner diameter of the bushing and only then weld the corresponding axle to the metal frame that we welded at the beginning.

Do-it-yourself garden wheelbarrow 2-wheeled: manufacturing instructions

Now we turn to the main part of our work - the body. As agreed, we will make it for the transportation of about 200 kg and somewhere in the same volume. Let's take a height of 40 centimeters (no longer necessary - it's bad to turn over), length - 80 centimeters along the bottom edge of the body and 100 along the top. Width - 60-70 centimeters, to your taste. Actually, now let's move on to the assembly process.

STEP 1: we procure scrap metal. Steel thickness - 2 mm. It's enough. Of course, if your plans include winning Mr. Olympia, then you can make a body of 3-4 mm steel. You must have such spare parts as shown in the figure, then you can make a garden wheelbarrow with your own hands, the drawings of which were provided above.

STEP 2: we weld it all together. Actually, there is nothing to explain here, we just take any welding machine and weld this Rubik's cube into a monolith.

STEP 3: reinforce the design with small corners. This item is relevant only if you used 1 mm thick steel to make a two-wheeled wheelbarrow with your own hands. Strengthenings remove the effect of "jelly", the car becomes monolithic. With a steel thickness of 2 mm, you don’t have to bother - it will stand as if rooted to the spot.

STEP 4: we install the "box" on our frame. We weld it in several places to the metal profile, to the corners and voila - our do-it-yourself wheelbarrow is ready! It remains now to give her a tolerable appearance.

STEP 5: paint. Do you have some old metal paint somewhere, or dried residue from painting a gate or garage? We dilute and paint. Quality is not needed here - it will be erased anyway, this is just for the best appearance of our design, so that a photo of a garden wheelbarrow with your own hands can be uploaded to a social network to collect likes!

Now it remains to do one little thing - a folding leg so that you can put the wheelbarrow in a horizontal position and conveniently load it. It will take no more than 30 minutes. We take the wheel from the old washing machine along with the mount, with a slight movement of the hammer we remove the wheel from the mount (or unwind it, depending on the design), weld the mount at the bottom of the wheelbarrow. Next, you need to take a metal profile 20x20 mm, drill a 10 mm hole at the end, insert an M10 bolt into the mount. Add a locknut to keep it from spinning. You should get a wheelbarrow similar to this:

A stop may be required for the leg (if you made poor calculations of the height and angle of attachment). You can weld some piece of metal that will be in the place of the necessary stop, or take a mount and wrap the leg mount in the right direction. However, these are already trifles and they are solved in the process. Now you know how to make a wheelbarrow with your own hands without spending money and you can go to the garage for all the necessary components. Also note that at the scrap metal collection point you can skimp well for a penny.

We invite you to watch a comparison of a purchased wheelbarrow and a do-it-yourself garden wheelbarrow in the video:

An ordinary do-it-yourself garden cart not only moves, but is also made - not only for reasons of saving on buying household goods in a store. There are many cases on earth that require regular or occasional transportation of goods, a purchased wheelbarrow can not cope with every type of ancillary rigging work.

Garden cart - an indispensable assistant in a country house

In gardening and farming, a garden cart, two-wheeled or four-wheeled, makes it easier to perform a variety of tasks. Removal of garbage and household waste, withered leaves and mowed grass, movement of building materials, firewood and coal - the range of use of small-scale wheeled vehicles is more than wide. When landscaping the territory with turf, when concreting the porch with your own hands, when laying out flower beds and greenhouses, arranging park paths, etc. an ordinary wheelbarrow increases the speed of work several times.

Of course, the easiest way is to buy a wheeled assistant in a store. Then you don’t have to think about how to make a garden cart reliable and voluminous with your own hands. But the choice of purchased wheelbarrows and carts is often limited to the only model that was developed during the construction of the White Sea-Baltic Canal - and since then they continue to be produced according to the well-known principle "The best is the enemy of the good". With self-production, the size and carrying capacity of the wheelbarrow is determined by the master himself, as well as its cross-country ability, because you can install wheels of various sizes.

In addition, in a populated country house or in a dacha with a personal plot, there is always a lot of conditionally ownerless materials - boards, bars, iron fittings and corners, etc. In this way, you can save on the purchase of original parts - a do-it-yourself garden wheelbarrow will be cheap in terms of costs, although it will require time and effort.

Garden wheelbarrow - do it yourself made of wood

A garden cart made of wood is the easiest to carry out, because. this process does not require the use of complex equipment such as welding machines or metal cut-off saws. The tree is processed with standard tools - but keep in mind that the durability, strength and load capacity of such a trolley will be noticeably inferior to the metal "sister".

Do-it-yourself garden wheelbarrow made of wood - step by step diagram

Step 1: the frame is the basis of reliability

The frame for a wooden cart is made of thick boards, in the form of a square or rectangle. The size of the bars for the frame is at least 70x70 mm, otherwise it will only be possible to carry hay and leaves on such a wheelbarrow. The frame of the beams is assembled "overlapped", screws are driven into the corners, it is possible to strengthen the frame structure with metal corners and additional ceilings. If there are antiseptic compounds on the farm, all the wood used is processed by them in advance - then our home-made wheelbarrow will resist rotting and dampness longer.

Step 2: Running

Rails for ball bearings are screwed to the bottom of the frame - one or two, depending on the number of wheels. It is better to make a wooden cart two-wheeled, providing supports for horizontal installation. If there is a ready-made axle on which you can put wheels from an old kart or moped, a bar with bearings is not needed.

A self-made wheelbarrow made of wood on one wheel will be unstable - high carpentry skills are required for such work.

Having fixed the wheels, the "skeleton" of the future trolley needs to be rolled around the site - it is better to fix the flaws in the wheel fasteners at an early stage. An inconvenient wheelbarrow will have to be used as an element of garden design or pushed deeper into the barn, so that a reminder of the inefficient expenditure of time and effort does not spoil our mood with its appearance.

Step 3: making the handle

The handle of the trolley has a large load during movement. It is advisable to make it out of metal, even when the wheelbarrow itself is made of wood. As a metal handle, a steering wheel from an old scooter or just a long steel stick with a rubber crossbar is suitable. It is best to mount the handle articulated, with a latch. This design will allow the mounting unit to be reliable and fold during storage - which means that a garden wheelbarrow with an articulated handle will take up less space, and the handle itself will not break from someone's careless movement.

Step 4: hull

On a solid frame with reliable wheels, you can install free-form bumpers made of boards or plywood - you get a classic garden cart, assembled by yourself. Actually, the cargo container itself is quite feasible in a removable version - for example, in the form of an old plastic tub for transporting liquids or bulk cargo. Or a used trough, which is inserted into the spacer between the bars stuffed onto the frame. A wooden wheelbarrow is good because it provides fasteners for various containers for transporting goods, this is impossible with an iron cart.

Garden cart - do-it-yourself metal

But metal has other advantages - it does not rot or crack, withstand a lot of weight and last for decades - if high-quality metal is chosen, all parts fit well and are welded to each other. The garden cart is four-wheeled and large-sized, for carrying loads up to 100 kg and more, made only of metal - no tree can withstand such a load.

DIY metal garden cart - step by step diagram

Step 1: container first

Yes, yes, unlike the wooden counterpart, the metal cart is assembled from top to bottom. That is, the dimensions of a steel trough or other container determine the dimensions of the frame - but not vice versa. It is advisable to immediately check the tightness of our container, then it can be used to transport liquid or pasty goods without the risk of leakage to your own garden plot.

A good option would be to install pneumatic (that is, pumped up by a pump) wheels on our metal cart. Firstly, it will increase its carrying capacity to 60-80 kg. Secondly, the wheelbarrow on pneumatic wheels will significantly increase the permeability. Thirdly, the wheel brake control can be brought to the handle - moving the trolley along inclined planes will become much easier, without the risk of tipping over or scattering the load.

The choice of drawing and design features of a two-wheeled cart

From words to deeds: how to make a homemade car in 4 hours

First, we will make a frame on which the body of the car will be installed. Our design is designed to carry no more than 200 kg, so keep this in mind and do not exceed the load to avoid tool breakage. Dimensions may vary, but we chose the average parameters that are most often used in garden and construction two-wheeled cars. Now let's move on to the selection of materials, tools and assembly of the structure.

STEP 1: Weld the 2 load-bearing sides together. You will need 2 metal profiles with sides 35x35 mm and a length of 140-150 cm, as well as a corner 25x25 mm 2 meters long. We lay metal profiles opposite on a flat surface, cut off 5 corners of 40 centimeters each and lay them out between our load-bearing sides of the frame. We weld the corners on both sides to the metal profile as shown in the diagram.

STEP 2: make the handles. We take a thick rubber hose with an inner diameter of 34 mm and a length of about 40 centimeters, cut it in half. A homemade garden wheelbarrow should have non-slip handles, so the hose is pulled very hard on the metal profile. It must be held over the fire, constantly scrolling, so that it warms up well. Then, with a slight movement of the hands (legs or improvised objects) or with the help of an auxiliary worker, we pull the hose onto the end of the frame, as shown in the diagram. The hose will cool down and it will no longer be possible to remove it. If it is difficult to pull, you can lubricate the metal with shampoo, soap or grease - in most cases it helps.

STEP 3: weld the axle. This can be done later, but we will do it now, because it is much more convenient. We turn our frame for a homemade wheelbarrow on wheels and weld a metal bar with a diameter of 22 mm (this is the running size for tubeless wheels). You can choose a different diameter, if you have any wheels for a wheelbarrow in mind. We recommend using truck tubeless wheels with a diameter of 40 to 50 cm - they are almost eternal.

If your homemade car for a summer residence has to carry a large load off-road (obstacles up to 5-8 cm in height), then it is better to use wheels with a larger diameter. If you have a very flat area or even concreted, it is better to choose 35-40 cm each, no more - there is less resistance, it is more convenient to control and it is easier to push. In addition, small wheels are cheaper.

Do-it-yourself garden wheelbarrow 2-wheeled: manufacturing instructions

STEP 1: procure scrap metal. Steel thickness - 2 mm. It's enough. Of course, if your plans include winning Mr. Olympia, then you can make a body of 3-4 mm steel. You must have such spare parts as shown in the figure, then you can make a garden wheelbarrow with your own hands, the drawings of which were provided above.

STEP 2: We weld everything together. Actually, there is nothing to explain here, we just take any welding machine and weld this Rubik's cube into a monolith.

STEP 3: we strengthen the structure with small corners. This item is relevant only if you used 1 mm thick steel to make a two-wheeled wheelbarrow with your own hands. Strengthenings remove the effect of "jelly", the car becomes monolithic. With a steel thickness of 2 mm, you don’t have to bother - it will stand as if rooted to the spot.

STEP 4: install the "box" on our frame. We weld it in several places to the metal profile, to the corners and voila - our do-it-yourself wheelbarrow is ready! It remains now to give her a tolerable appearance.

STEP 5: paint. Do you have some old metal paint somewhere, or dried residue from painting a gate or garage? We dilute and paint. Quality is not needed here - it will be erased anyway, this is just for the best appearance of our design, so that a photo of a garden wheelbarrow with your own hands can be uploaded to a social network to collect likes!

We invite you to watch a comparison of a purchased wheelbarrow and a do-it-yourself garden wheelbarrow in the video:

rabotai-sam.ru

How to make a garden wheelbarrow with your own hands?

It is difficult for a summer resident who keeps order on his site to do without a garden wheelbarrow. It is indispensable when you need to remove and take out the garbage outside the site. With its help, you can move various loads, harvest and carry out other work. You can buy a garden wheelbarrow at any hardware store, but it’s much more interesting to make it yourself.

It is difficult for a summer resident who keeps order on his site to do without a garden wheelbarrow.

The garden trolley should be reliable and convenient. Most often, it is used in the garden or in the garden, so it must be maneuverable so that it is easy to move along narrow paths with it and simply unload it by lifting the handles a little and turning the contents inside out.

Preparatory activities

In order to make a convenient trolley for a summer residence, complex drawings and tools are not required. For its manufacture, you can use any material, for example, wood.

Coniferous trees are not suitable for this purpose.

In order to assemble a garden wheelbarrow with your own hands, you need to prepare. For work you will need:

Wheelbarrow assembly diagram.

Wooden boards and bars.
Fasteners (screws, washers, nuts).
Wood saw or circular saw.
Wrench.
Pencil.
Sandpaper.
PVA glue.
Threaded metal pin.
Drill and drill bits for it.

Manufacturing of main parts

Work should begin with the manufacture of the box. To do this, you need pieces of boards. Their dimensions will depend on the dimensions of the future design. The standard size of a dacha wheelbarrow is 450 mm wide and 550 mm long. If necessary, the dimensions can be changed.

Next, prepare the wheel. If the farm did not find a metal wheel, then it can be made from wood. To do this, you need 6 pieces of boards measuring 300x150x20 mm. Using PVA glue, they need to be glued into a square as follows: 2 planks are stacked so that they touch with their long sides. The next 2 are placed on top so that the point of contact is perpendicular. The last planks are laid in the same way as the first. The resulting design should be put under a press and left until the glue dries completely. This will take at least 24 hours.

Next, you need to mark the circle. The diameter of the future wheel will be 270-280 mm. For greater reliability, the wheel blank should be fastened with self-tapping screws or bolts. A circle is drilled according to the marking. Rough edges of the workpiece should be processed with sandpaper.

To mount the wheel and box, you will need a mounting frame - the main supporting part of the trolley. To assemble it, you will need 2 bars 1200 mm long and at least 50 mm thick. The protruding parts of the bars will play the role of handles.

It is better to collect parts on a flat surface. The bars should be placed side by side, connecting the ends on one side. The ends on the opposite side should be spread apart to a distance equal to the width of the shoulders of the person who will use the wheelbarrow.

At the ends of the bars connected together, you need to make a mark for the future fastening of the wheel. To do this, a beam of smaller diameter is laid on them and a mark is placed on the frame. A cut is made from the intended line to the end of the frame.

Assembly of all parts

In order for a wooden cart to serve for many years and be strong and reliable, you should choose hardwood: oak, maple, elm, birch.

Before putting the wheel in its place, it is necessary to install a spacer between the frame bars. It is installed in such a way that a wheel fits between the pre-cut ends. If the wheel width is 60 mm, then a distance of 90 mm must be left between the bars. These parameters will help determine the size of the spacer itself. Its ends must be cut and then attached to the bars with bolts.

To mount the wheel, you will need a metal stud with a thread 200 mm long, 4 washers and 4 nuts with a diameter of at least 12-14 mm. At the end of the bars, it is necessary to drill a hole for the stud. In the middle of the wheel, it is also necessary to prepare a hole, the diameter of which should be slightly larger than that of the stud. When everything is ready, you can start assembling. The pin is threaded through a hole on one bar. A washer is put on it, then a nut, then a wheel is mounted, then another nut and a washer. After that, the hairpin is threaded through the hole on the second beam. From the outer sides of the bars, the wheel is fixed with washers and nuts. The pin must be rigidly fixed to the bars. To achieve this, you will need two wrenches.

When all the details are ready, you can start assembling the wheelbarrow. The box is turned upside down, and a mounting frame with a wheel is placed on it. It must be installed so that the wheel does not touch the box. Using a pencil, the location of the frame on the bottom of the box is marked so that it is possible to set the wooden wedges as accurately as possible. Their thickness must be at least 50 mm, width - 100 mm. According to the marked lines, the wedges are attached to the bottom with bolts, and then a frame with a wheel is attached to them. To make the wheelbarrow convenient to use, spacers must be fixed on the side walls of the box. Their length should be such that the box mounted on them is parallel to the ground. Thanks to this, the cottage trolley will stand evenly and steadily during loading and unloading operations. For greater rigidity of the racks, they can be strengthened with a spacer, one end of which is attached to the rack, and the other to the bottom of the box.

The finished country cart should be covered with drying oil. This will protect the wood from damage and extend its life. If, after many years of operation, the trolley has retired, do not rush to throw it away. It will serve as an excellent decor for a summer cottage, if you use it, for example, as a large flower pot.

Another trolley option

The country cart can be made of metal. The result is a versatile model that can be used in heavier jobs such as construction. To make it, you will need a welding machine and skills to work with it.

The trolley box can be made from a sheet of metal with a thickness of about 2 mm. The frame and handles should be welded to it. As for the wheel, you need to choose it, focusing on the load that the finished inventory will experience.

The box can be any size. In order to more accurately perform the work, it is advisable to draw up a diagram of the future product, on which to apply all the details and indicate their dimensions. According to the sketch, a sheet of metal is cut by a grinder and then welded into a box. For the manufacture of racks, you can use a metal corner or pipe sections. In order not to make the structure heavier, it is better to make handles from a thin-walled pipe.

To make the job as cheap as possible, you can use an old metal barrel to make the box. First you need to build a supporting frame. To do this, you can use any material that is on the site: pipe, profile, square. Attach the wheel to the bow of the structure. Opposite ends will act as handles. The barrel should be cut lengthwise into two parts and one fixed on the frame. To ensure stability for the wheelbarrow, racks in the form of pipes or arcs must be welded under the supporting frame.

DIY garden cart

Samodelkin 23-03-2016, 04:40 16 086

In contact with

Every summer resident, gardener, villager in his household cannot do without a cart or wheelbarrow. In the dacha economy, it is often necessary to take out the garbage accumulated during the season. In the spring-autumn season, most of all cargo transportation, in the fall the leaves of the branch, in the spring the re-preservation after the winter, the garbage is also from somewhere. In the village, a wheelbarrow is always needed because there is a lot of work.

Today, in building stores there is a huge selection of garden wheelbarrows for every taste and budget. The design of shopping carts is certainly rather weak for our operational working conditions. Yes, and if the plot is large and you need a bigger wheelbarrow. So the author thinks the same way and decided not to look for easy ways, but to make a garden wheelbarrow with his own hands. A brief principle of operation of the trolley, the load placed in the body of the trolley will put pressure on the wheel with its mass, lifting the levers by the handles, we shift the weight onto the wheel and it becomes easier for us and the wheel takes on the entire mass of the load. This is shown in the picture.

But the author decided to make a two-wheeled cart, but the principle remains the same. And so what does the author need to create his idea?

Materials: boards 30 mm, pipe, 16 mm, two wheels, roofing iron, washers, nuts, bolts.

Tools: a welding machine, a drill, a set of keys, a hammer, a hacksaw, an ax. First, a diagram.
To begin with, the author sawed off a piece of pipe to size and welded the axles for the wheels.
Then he made a frame of wooden boards and bars. Inside the body was covered with iron.
I screwed the pipe with wheels to the trolley bridge with brackets.
Then I screwed the handle to the trolley and in fact everything is ready.
Now the author has such a wonderful cart. Source Become the author of the site, publish your own articles, descriptions of homemade products with payment for the text. Read more here.

In contact with

To write a comment, you must enter the site through the social. network (or register): Regular registration

Information

Visitors in the Guests group cannot leave comments on this post.

usamodelkina.ru

How to make a garden wheelbarrow with your own hands.

A garden plot is not easy to keep in order. There is always a pile of rubbish, dry branches, construction debris, and carrying heavy loads all the time is hard. It is difficult and not easy for people who are in old age, and there are more and more such lovers to maintain a personal plot. In order not to carry burdens, but to spend time in a summer cottage, you can make a garden wheelbarrow with your own hands.

A garden wheelbarrow made by hand from hand-made materials will become an indispensable assistant in the garden. Special skills for the construction of the device are not required, and all the necessary materials can be taken at your dacha or bought at a hardware store.

Types of wheelbarrows

Depending on the work and the number of wheels, wheelbarrows are divided into several types. For construction work, metal wheelbarrows with one wheel are used. For work in the garden and garden, you can also use wooden wheelbarrows with one wheel.

Devices for moving heavy loads with two or more wheels are called a trolley.

Varieties of garden wheelbarrows can be seen in the photo:

The main and most important advantage of a wheelbarrow is its reliability. Maneuverability also plays an important role. If a person uses a wheelbarrow in a garden or garden plot, a narrow path will suffice, along which a one-wheeled wheelbarrow can be rolled. It can also be easily unloaded and turned over the contents by slightly lifting the handle of the wheelbarrow.

Unfortunately, you can’t drive a two-wheeled wheelbarrow along a narrow path, there is a chance to spoil and crush the plants.

To maintain balance and stability, it is necessary to build a wheelbarrow with spacers. And when you load it with a heavy load, make sure that it does not turn over and try to support or prop it up on one side.

The main advantage of a two-wheeled wheelbarrow is its stability. And when such a device is loaded, there is no chance of rollover.

On a two-wheeled wheelbarrow it is convenient to transport building material, long boards, large branches. It is advisable to load them so that the center of gravity is in the middle of the body.

The design of the wheelbarrow can be different, with one handle or two. One transverse handle is much more convenient, since you can hold on to it with one hand, and the second will be free.

We make a wheelbarrow from wood

Making a wooden wheelbarrow yourself is quite simple; drawings of a garden wheelbarrow can be omitted. You can do without them. If some material is not enough, it can always be purchased at a hardware store.

For a garden wheelbarrow, it is preferable to take hardwood. The best option would be oak, birch, maple or elm. Such a wheelbarrow will serve much longer, and the design will be strong and reliable. Coniferous wood is better not to use.

Necessary materials:
Wooden boards for the box.
Wooden bars for the base.
Boards for making wheels.
Screws, washers, nuts.
Circular saw or hacksaw.
Pencil or marker.
Drill.
PVA glue.
Sandpaper.
Metal rod with thread.
Wrench.
Welding machine.

How to make a mounting frame

Take the boards, plan them and assemble the base in the form of a box. The size of the wheelbarrow is at your discretion, be guided by the preferences of what you will transport. The standard size of a country cart is 45 centimeters wide and 55 centimeters long. You can add a centimeter in each value.

To build a cart, you will also need a wheel. If you plan to build a one-wheeled garden wheelbarrow, then prepare one wheel. To create a two-wheeled garden wheelbarrow, you need two wheels.

The finished box and wheel must be strengthened on the base. To build the main supporting part of our wheelbarrow, you need to take two identical wooden blocks. The thickness of the beam should be about 3-5 centimeters, and the length of a meter is 20 centimeters. The bars will automatically become our handles, the edges of which will be convenient to hold on to move the load around the summer cottage.
For the convenience of assembling all parts of the trolley, it is advisable to put the bars on a flat surface (it can be a table) and connect them together - ends to ends. And spread the opposite ends to the side, the width should be the same as the width of the shoulders of the person who will use the wheelbarrow.
After laying out the bars on a flat surface, we put a wooden bar of small diameter on top. We outline its outlines with a pencil or marker so that a parallel line is defined on the frame. We outline the place of fastening of the wheel.
Where the lines are marked, you need to cut with a hacksaw or a circular saw.

Making a wooden wheel

If it is not possible to purchase a metal wheel, you can make a wooden one yourself. For this, a hardwood is taken (to avoid rotting). The diameter of the wheel will be 27-28 centimeters.

To assemble the wheel, you need to prepare the planks in advance, plan them. The size of the boards is 30x15x2 centimeters, the number is six pieces. They need to be glued so that a square is obtained. You can glue it with ordinary PVA glue. After gluing, the structure must be put under pressure for 24 hours.
After gluing the square, using a pencil or marker, you need to mark the circle. Before you start drilling the wheel, with the help of bolts, it is advisable to fasten the structure. Drill according to the basting, treat the surface with sandpaper or a rasp.

If the wheelbarrow will be actively used to move heavy objects, then it is better to buy a metal wheel. In principle, the installation of both a wooden wheel and a finished metal one with a rubber tire is no different.

How to mount the wheel and frame

To attach the wheel to the wheelbarrow, you need to connect the bars using a spacer. It is installed so that the wheel is inserted. If the width of the wheel is about 5-6 centimeters, then the distance should be 8-9 centimeters. Therefore, the spacer can be prepared in advance, washed down, especially at the ends and attached with bolts to the bars.
To mount the wheel, you can use a long metal rod (stud) that has a thread (thread length up to 200 mm. It is also necessary to prepare four washers and nuts with a diameter of up to 14 mm.
It is necessary to make a hole for the rod at the end of the bars. And in the middle of the wheel, drill a hole larger than the diameter of the stud. Next, we assemble and fix the wheel with a washer and nut. The stud should be well fixed, you can check this with a wrench. If loose, tighten with two wrenches.

If a wheelbarrow is assembled from metal, its body must be welded to the frame using a welding machine.

Assembly

Turn over the wheelbarrow box and put the base with the wheel installed on top, but so that the wheel does not reach the box itself. Use a marker or pencil to mark where the frame lies. This is necessary for sawing wooden wedges. Their thickness should be about 5 centimeters, the width is twice as large. They need to be attached along the marked lines to the box with bolts and wedges to attach the base with the wheel.

The finished wheelbarrow must be covered with drying oil. So the tree will last much longer and will be protected from decay.

In order for the garden wheelbarrow to be carefully operated, it must be installed on spacers.

After the wheelbarrow fails (in a few decades), it can be used as a flower bed.

Assembling a wheelbarrow from metal

We assemble a metal garden wheelbarrow. This design will be much more durable and will last for many years. It can be used both during harvesting and during construction to move sand and cement.

It is not difficult to make a metal wheelbarrow with your own hands. All that will be needed is the presence of a welding machine and the skills to operate it.

For example, a garden wheelbarrow can be welded from sheet metal 1-2 mm thick. First, you need to assemble the body from the sheet and then attach the wheel and handle to it. If a large load is expected on the wheelbarrow, it is advisable to install a powerful wheel, for example, from an old moped, bicycle, and even a motorcycle.

Let's start making a wheelbarrow. We take a sheet of steel a meter by two, 1 mm thick. In advance, you need to purchase wheels with a diameter of up to 40 cm, choose those on which bearings are already installed.

The box can be made of any size, with a capacity of about 100 liters.

To do the job exactly, you need to draw a sketch, apply dimensions, indicate all the details.

For work, you will need a welding machine and a grinder. The sheet must be “cut” according to the sketch and the box must be welded. Racks for support should be made from a metal corner measuring 25x25; instead of a corner, you can take a piece of a metal pipe of the desired diameter. The handle for the wheelbarrow can be constructed from thin-walled pipe so that the wheelbarrow itself is not too heavy. Optionally, you can make a wheelbarrow with two handles.

Garden wheelbarrows and carts are familiar to anyone who has a personal plot or cottage, builds a house, barn or garage.

You can’t do without them when you need to move a large amount of soil, fertilizers, building materials and other goods.

Anyone who has not yet acquired a wheelbarrow or cart, but is going to buy them in the near future, should have a correct idea of the varieties of this inventory.

It is equally important to correctly assess its advantages and disadvantages, as well as consider options for self-production. We will try to answer all these questions in detail.

Types and design features of garden wheelbarrows

All wheelbarrows and carts intended for garden and construction work, depending on the number of wheels, are divided into several types. At the same time, only one-wheeled carts are usually called wheelbarrows. Two, three and four wheeled structures according to the generally accepted classification are called carts.

The main advantages that a garden wheelbarrow attracts the attention of buyers are its high maneuverability and reliability. Another, no less important advantage is the minimum wheel track width.

In the garden, a narrow path between the beds is enough to move a one-wheeled wheelbarrow. You cannot pass a two-wheeled cart in such a tight "corridor" without crushing the plants. A wheelbarrow with one wheel is easy to unload. To do this, just lift its handles or tilt them in the right direction.

However, ease of unloading and good maneuverability come at a high price. A standard garden wheelbarrow is unstable, so when loaded, you will have to make an effort to maintain balance. When loading, you need to monitor the stability of the wheelbarrow so that it does not roll over.

The main advantage of a two-wheeled garden cart is stability.. An axle with two wheels and loading stops prevent it from tipping over. When in motion, a properly loaded garden cart will never tip over.

In addition to bulk materials, it can transport heavy long loads (boards, branches or timber). To do this, they must be placed so that the center of gravity is inside the loading platform.

By design, garden carts are produced with one transverse handle or two longitudinal, like a wheelbarrow. The cross handle is more convenient to use, because you can hold on to it with one hand and pull the cart along, controlling the bumps in the road. In this way, moving heavy loads is much easier than pushing them in front of you. It is much more difficult to do the same maneuver with a two-handed cart.

When choosing this household equipment, you should pay attention to the design of the thrust racks. A loaded garden cart with two stationary stops will cling to it when driving on uneven ground. If the emphasis is one and at the same time folding, then it is much more convenient to carry such a cart.

The size of the wheels and their depreciation - two more points which you need to focus on when buying. A one-wheeled wheelbarrow creates a lot of pressure on the ground, which worsens its patency. Two-wheeled carts are ideally suited for working on soft ground in this respect.

Too small wheels on a wheelbarrow and a trolley are an unfortunate solution, since they do not overcome uneven ground well. Therefore, choose wheels for a garden wheelbarrow larger. It is desirable that they be inflatable and stand on a metal, not a plastic rim.

Regarding the material from which manufacturers make cargo bowls (body) of wheelbarrows and carts, it should be said that aluminum for garden tools is preferable to steel. This metal is light, not afraid of corrosion and does not require regular tinting.

Steel outperforms aluminum in strength, but loses in weight and rust resistance. Therefore, a wheelbarrow with a steel body is more suitable for transporting heavy building materials, rather than compost and fertilizer for the garden.

Prices

The cost of garden wheelbarrows and carts directly depends on the design, volume of the body (trough) and the number of wheels. The cheapest one will cost you a one-wheeled wheelbarrow (trough volume 80 liters, wheel diameter 38 cm, weight 9-10 kg). Its cost is in the range from 1100 to 1300 rubles.

If there is a need to transport building materials, large volumes of soil and fertilizers, then a two-wheeled cart would be the best option. The cost of this home assistant starts from 1400 rubles. and ends at around 3000 rubles.

At the same time, choose a design with a reinforced frame, reliable stops and inflatable wheels on steel disks.

We make a garden cart with our own hands

A home master, who has a set of metalwork tools, never rushes to the store for household equipment, but makes it with his own hands.

Both garden and construction wheelbarrows have no fundamental structural differences, with the exception of a more durable structure, which is necessary for transporting bricks, crushed stone or cement.

To make a trolley, you will need a standard cold-rolled steel sheet measuring 1x2 meters and 1 mm thick. It is better to buy pneumatic wheels for it with a diameter of 35 to 40 cm with installed bearings.

The tube for the shaft must be of such a diameter that it can be inserted tightly into the wheel bearings, and the protruding ends should be fixed with a nut and cotter pin from unscrewing.

You can choose the volume of the bowl for a homemade trolley that you need most often (from 70 to 110 liters).

In order to make a garden wheelbarrow with your own hands, you should draw a detailed sketch. On it you need to indicate the configuration and dimensions of the unfolding of the cargo bowl, the design of the support legs of the wheel axle, as well as handles and stops.

After that, the grinder and the welding machine come into play. The sheet is cut according to the sketch, and then a cargo bowl (trough) is welded from the received parts.

The support legs of the wheel axle can be made from a 25x25 mm corner or a tube by welding a steel ring into it from a piece of pipe of a suitable diameter. The trolley handle and its supporting cargo racks are best made from a thin-walled tube so as not to weigh down the structure.

If the option of two stationary racks does not build you, make one central one, having thought over for it your own version of the hinged-folding design.

Amin. Meaning. name and destiny. The meaning of the name Aminat: origin, character and fate What does the name amine mean

Funeral home "grail" According to numerology, which means the number 9

Why dream of being late in a dream book

Why is the big black spider dreaming?